• Offered by Research School of Engineering
  • ANU College ANU College of Engineering and Computer Science
  • Course subject Engineering
  • Areas of interest Information Technology, Engineering
  • Academic career UGRD
  • Course convener
    • Nicolo Malagutti
  • Mode of delivery In Person
  • Offered in First Semester 2014
    See Future Offerings

This course provides an introduction to the analysis and design of digital systems and microprocessors. Review of combinational analysis and design. Analysis and design of synchronous finite state machines and register transfer level systems. Computer aided design and programming of digital electronic circuits through the application of several modern software packages. A detailed introduction to VERILOG hardware description language. Extensive hardware labs involving the implementation of complex digital systems in FPGA programmable logic devices. Microprocessor devices, their architecture and instruction sets. Hardware aspects of instruction execution. Assembly language and C programming. Input/output, bus interfacing, interrupts. Co-design of digital hardware and microprocessor systems.

Learning Outcomes

Upon successful completion, students will have the knowledge and skills to:

Upon completion of this course, students will have the knowledge and skills to

  • Use top-down design to translate system requirements into a practical digital design.
  • Design complex digital systems through finite state machines and the register transfer level technique and implement these in programmable logic.
  • Learn fixed point DSP.
  • Learn how to program in C and VERILOG HDL.
  • Learn to use ISE WebPACK to realise complex digital designs in FPGAs.
  • Learn about and use free and open source design software.
  • Learn practical electronics testbench skills and the ability to communicate appropriately via a lab notebook.
  • Learn to build and use microprocessors

Indicative Assessment

Assessment (10%) Midterm Exam (20%) Labs (30%) Exam and Project (40%)

The ANU uses Turnitin to enhance student citation and referencing techniques, and to assess assignment submissions as a component of the University's approach to managing Academic Integrity. While the use of Turnitin is not mandatory, the ANU highly recommends Turnitin is used by both teaching staff and students. For additional information regarding Turnitin please visit the ANU Online website.


21 lectures plus 3 hours of LABS per week.

Requisite and Incompatibility

To enrol in this course you must have completed ENGN2218 or COMP2300.

Prescribed Texts

Reading Material

  • Text book - John F Wakerly (Digital Design, Principles and Practices, Prentice Hall) - available now in the book shop.
  • There is a reading brick from 2008.  It is now out of date but we still cover everything in it.

There are a number of other texts eg:

  • Vahid and Lysecky (Verilog for Digital Design, Wiley): good for RTL verilog.
  • Milos Ercegovac (Introduction to Digital Systems, Wiley. Chs 13-15) good for RTL design but all in VHDL and
  • Furber (ARM SoC Architecture, Addison-Wesley): background reading for later on in the course.

Reading Material On the WEBSITE

  • The old brick (ENGN3213 2008 Brick.pdf). There are a limited number available in hardcopy for AUD 7. 
  • The detailed tour of the (course lecture3 and 4.pdf). This is lectures 3-4 and it will prove useful to download it already for tomorrow's lecture.
  • PICOBLAZE manuals: hardware manual (xapp213.pdf) and C compiler (pccomp manual.pdf)
  • Datasheets for Xilinx FPGAs
  • Several documents on Finite State Machines (FSMs), Register Transfer Level (RTL) Design and VERILOG HDL
  • The CLAB and HLAB manuals will become available as needed.




Tuition fees are for the academic year indicated at the top of the page.  

If you are a domestic graduate coursework or international student you will be required to pay tuition fees. Students continuing in their current program of study will have their tuition fees indexed annually from the year in which you commenced your program. Further information for domestic and international students about tuition and other fees can be found at Fees.

Student Contribution Band:
Unit value:
6 units

If you are an undergraduate student and have been offered a Commonwealth supported place, your fees are set by the Australian Government for each course. At ANU 1 EFTSL is 48 units (normally 8 x 6-unit courses). You can find your student contribution amount for each course at Fees.  Where there is a unit range displayed for this course, not all unit options below may be available.

6.00 0.12500
Domestic fee paying students
Year Fee Description
1994-2003 $1650
2014 $2952
2013 $2946
2012 $2946
2011 $2946
2010 $2916
2009 $2850
2008 $2592
2007 $2298
2006 $2190
2005 $2190
2004 $2190
International fee paying students
Year Fee
1994-2003 $3450
2014 $3762
2013 $3756
2012 $3756
2011 $3756
2010 $3750
2009 $3618
2008 $3618
2007 $3618
2006 $3618
2005 $3534
2004 $3450
Note: Please note that fee information is for current year only.

Offerings, Dates and Class Summary Links

ANU utilises MyTimetable to enable students to view the timetable for their enrolled courses, browse, then self-allocate to small teaching activities / tutorials so they can better plan their time. Find out more on the Timetable webpage.

The list of offerings for future years is indicative only.
Class summaries, if available, can be accessed by clicking on the View link for the relevant class number.

First Semester

Class number Class start date Last day to enrol Census date Class end date Mode Of Delivery Class Summary
3474 17 Feb 2014 07 Mar 2014 31 Mar 2014 30 May 2014 In Person N/A

Responsible Officer: Registrar, Student Administration / Page Contact: Website Administrator / Frequently Asked Questions